Logo

B0102 Engine Trouble Code

B0102 Engine

When you check engine light came on code B0102 the reason should be . However your vehicle's manufacturer may have a different definition for the B0102 OBD-II Diagnostic Body (B) Trouble Code. So you should chech it on our car models.

When your car's 'B0102 Check Engine' light comes on, it's usually accompanied by a sinking feeling in the pit of your stomach. The light could mean a costly problem, like a bad catalytic converter, or it could be something minor, like a loose gas cap. But in many cases, it means at minimum that you'll be visiting the car dealer to locate the malfunction and get the engine conducted light turned off.

B0102 Code Meaning :

B
OBD-II Diagnostic Body (B) Trouble Code For Engine
0
Intake Valve Control Solenoid Circuit Low
1
Engine Oil Temperature Sensor Malfunction
0
Cylinder 10 Contribution/balance Fault
2
Crankshaft Position Sensor A Circuit Low Input

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

B0102 OBD-II Diagnostic Body (B) Trouble Code Description

B0102 engine trouble code is about Crankshaft Position Sensor A Circuit Low Input. Engine Oil Temperature Sensor Malfunction and Cylinder 10 Contribution/balance Fault causes most of code B0102.

Reason For B0102 Code

The reason of B0102 OBD-II Engine Trouble Code is Engine Oil Temperature Sensor Malfunction.

B0102 DTCs may also be triggered by engine faults earlier down the line. For example, a dirty MAF sensor might be causing the car to overcompensate in its fuel-trim adjustments. As a result, oxygen sensors are likely to report fuel mixture problems.

How To Repair B0102 Code

Before starting let's see B0102 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access B0102 code stored in the ECU.
  • Technicians will note B0102 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

A knocking sound that comes out of your bonnet is a definitive sign of an engine that is failing. Engine damage wear can cause this sound in your engine's technical components such as pistons, bearings or other motioning components.Some recurrent solutions for this situation might be in replacing the spark plugs, testing and replacing your ignition coils.

A digital volt/ohmmeter may be necessary to compare the voltage reading with the manufacturer’s specifications. The mechanic should always clear the code and retest the system after each possible repair, to ensure that they’ve made the proper diagnosis.

Sometimes B0102 code comes with B010200 code.

Diagnosis Of Engine Error OBD Code B0102

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a B0102 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the B0102 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.